Nosso Blog

Osciloscópio com gerador arbitrário via USB série Pico 2200

Osciloscópio com gerador arbitrário via USB da série Pico 2200 são modelos com dois canais de osciloscópio com banda de 10 a 200MHz , taxa de amostragem de 100MS/s a 1GS/s , 8(12) bits de resolução , profundidade de memória de 8 a 40KS  .

220xA-in-pocket  monitor2000Compact

Osciloscópio com gerador arbitrário

Especificações técnicas :

Osciloscópio com gerador arbitrário  – vertical
Model PicoScope 2204A PicoScope 2205A PicoScope 2206A PicoScope 2207A PicoScope 2208A
Input channels 2
Bandwidth 10 MHz 25 MHz 50 MHz 100 MHz 200 MHz
Rise time (calculated) 35 ns 14 ns 7 ns 3.5 ns 1.75 ns
Input type BNC
Vertical resolution 8 bits
Enhanced vertical resolution Up to 12 bits
Input sensitivity 10 mV/div to 4 V/div (10 vertical divisions)
Input ranges ±50 mV, ±100 mV, ±200 mV, ±500 mV, ±1 V, ±2 V, ±5 V, ±10 V, ±20 V
Input coupling Software selectable AC/DC
Input characteristics BNC, 1 MΩ ∥ 14 pF BNC, 1 MΩ ∥ 13 pF
DC accuracy ±3% of full scale
Analog offset range
(vertical position adjust)
none ±250 mV (50 mV to 200 mV ranges)
±2.5 V (500 mV to 2 V ranges)
±20 V (5 V to 20 V ranges)
Overvoltage protection ±100 V (DC + AC peak)

 

Osciloscópio com gerador arbitrário – horizontal
Maximum sampling rate (real-time)
1 channel
2 channel
100 MS/s
50 MS/s
200 MS/s
100 MS/s
500 MS/s
250 MS/s
1 GS/s
500 MS/s
1 GS/s
500 MS/s
Maximum sampling rate (repetitive signals, ETS mode) 2 GS/s 4 GS/s 5 GS/s 10 GS/s 10 GS/s
Maximum sampling rate
(continuous streaming mode)
1 MS/s 9.6 MS/s
Maximum waveforms per second 2200 3300 5700 6300 8500
Timebase ranges 10 ns to 5000 s/div 5 ns to 5000 s/div 2 ns to 5000 s/div 1 ns to 5000 s/div 500 ps to 5000 s/div
Buffer memory# 8 kS 16 kS 32 kS 40 kS 48 kS
Buffer memory (streaming mode) 2 MS per channel in PicoScope software. 100 MS (shared) in PicoScope software.
Waveform buffer
normal triggering
rapid block triggering
Up to 10,000 waveforms
not applicable
Up to 10,000 waveforms
Up to 32 waveforms
Timebase accuracy ±100 ppm ±50 ppm
Sample jitter < 30 ps RMS < 5 ps RMS

# Buffer memory is shared between active channels.

Dynamic performance (typical)
Crosstalk (full bandwidth) Better than 200:1 (equal ranges) Better than 400:1 (equal ranges)
Harmonic distortion < -50 dB at 100 kHz, full–scale input
SFDR > 52 dB at 100 kHz, full–scale input
Noise < 150 μV RMS (±50 mV range) < 200 μV RMS (±50 mV range)
Bandwidth flatness (at scope input) (+0.3 dB, -3 dB) from DC to full bandwidth

 

Triggering
Sources Ch A, Ch B
Trigger modes None, auto, repeat, single None, auto, repeat, single, rapid (segmented memory)
Advanced triggers Edge, window, pulse width, window pulse width, dropout, window dropout, interval, logic.
Trigger types, ETS Rising or falling edge
Trigger level Adjustable over whole of selected voltage range
Trigger sensitivity Digital triggering provides 1 LSB accuracy up to full bandwidth. In ETS mode, typical 10 mV p-p at full bandwidth
Maximum pre-trigger capture 100% of capture size
Maximum post-trigger delay 4 billion samples
Trigger rearm time PC-dependent < 2 µs on fastest timebase
Maximum trigger rate PC-dependent Up to 32 waveforms in a 64 μs burst

 

Function generator
Standard output signals Sine, square, triangle, DC voltage, ramp, sinc, Gaussian, half-sine
Pseudorandom output signals None White noise, PRBS
Standard signal frequency DC to 100 kHz DC to 1 MHz
Sweep modes Up, down, dual with selectable start/stop frequencies and increments
Output frequency accuracy ±100 ppm ±50 ppm
Output frequency resolution < 0.01 Hz
Output voltage range ±2 V
Output adjustments Any amplitude and offset within ±2 V range
Amplitude flatness (typical) < 1 dB to 100 kHz < 0.5 dB to 1 MHz
DC accuracy ±1% of full scale
SFDR > 55 dB @ 1 kHz full–scale sine wave > 60 dB @ 10 kHz full–scale sine wave
Connector type Front panel BNC with 600 Ω output impedance
Overvoltage protection ±10 V

 

Arbitrary waveform generator
Update rate 1.548 MS/s 20 MS/s
Buffer size 4 kS 8 kS
Resolution 12 bits
Bandwidth >100 kHz >1 MHz
Rise time (10% to 90%) < 2 µs < 120 ns

 

Spectrum analyzer
Frequency range DC to 10 MHz DC to 25 MHz DC to 50 MHz DC to 100 MHz DC to 200 MHz
Display modes Magnitude, peak hold, average
Window types Rectangular, Gaussian, triangular, Blackman, Blackman–Harris, Hamming, Hann, flat–top
Number of FFT points Selectable from 128 to half the available buffer memory in powers of 2
Scale / units X axis : linear or log 10
Y axis : logarithmic (dbV, dBu, dBm, arbitrary) or linear (volts)

 

Math channels
Functions −x, x+y, x−y, x*y, x/y, x^y, sqrt, exp, ln, log, abs, norm, sign, sin, cos, tan, arcsin, arccos, arctan, sinh, cosh, tanh, freq, derivative, integral, min, max, average, peak, delay
Operands A, B (input channels), T (time), reference waveforms, constants, Pi

 

Automatic measurements
Oscilloscope mode AC RMS, true RMS, cycle time, DC average, duty cycle, falling rate, fall time, frequency, high pulse width, low pulse width, maximum, minimum, peak to peak, rise time, rising rate.
Spectrum mode Frequency at peak, amplitude at peak, average amplitude at peak,
total power, THD %, THD dB, THD plus noise, SFDR, SINAD, SNR, IMD
Statistics Minimum, maximum, average and standard deviation

 

Serial decoding
Protocols CAN, LIN, I²C, UART/RS-232, SPI, I²S, FlexRay
Inputs All input channels with any mixture of protocols

 

Mask limit testing
Mask generation Auto generate from captured waveform, manual drawing, manual coordinate entry
Actions Highlight on screen, select in buffer overview, activate alarm
Statistics Pass/fail, failure count, total count

 

Alarms
Initiating events Capture, buffer full, mask fail
Alarm actions Beep, play sound, stop/restart capture, run executable, save current buffer/all buffers, trigger signal generator

 

Display
Interpolation Linear or sin(x)/x
Persistence modes Digital color, analog intensity, fast, custom

 

Data export
Output file formats BMP, CSV, GIF, JPG, MATLAB 4, PDF, PNG, PicoScope data, PicoScope settings, TXT
Output functions Copy to clipboard, print

 

Environmental
Temperature range (operating) 0 °C to 50 °C
Temperature range (stated accuracy) 20 °C to 30 °C
Temperature range (storage) –20 °C to +60 °C
Humidity range (operating) 5% to 80% RH non-condensing
Humidity range (storage) 5% to 95% RH non-condensing

 

Physical properties
Dimensions (including connectors) 142 x 92 x 19 mm
Weight < 0.2 kg (7 oz)

 

Clique em assuntos relacionados com sua pesquisa

Osciloscópio digital educacional Inove PO1022C

Osciloscópio tipo caneta Pico 2105

Osciloscópio MSO com gerador arbitrário e analise lógica em um

Osciloscópio PC Picotech da série 3000

BK 2190D Osciloscópio digital 100MHz

Osciloscópio de armazenamento digital BK 2190E

Osciloscópio de campo com canal isolado serie 2510 da BK Precision

Osciloscópio de armazenamento digital BK 2190E

Osciloscópio Tektronix TBS1000 bandas entre 25 e 150MHz

TDS 2000 C osciloscópios Tektronix de 50MHz a 200MHz

Osciloscópio com gerador arbitrário é na PerCon

Osciloscópio com gerador arbitrário e outros produtos da Pico Technology podem ser encontrados na PerCon Tecnologia que atua como canal de distribuição dos melhores fabricantes mundiais de soluções de teste e medição e é sediada no Rio de Janeiro na Rua Dias da Cruz 188 – Sub solo – Méier (percon@acessopercon.com.br) / Fone : 21-2596-8369

Clique aqui para comprar este produto

Osciloscópio com gerador

Fique por dentro!

Seja avisado sempre que surgir conteúdo novo por aqui.